Quality Woodworking Tools
Quality Woodworking Tools
 



Miller Dowel Joinery Kits


Woodworking Tools >  Miller Dowel Joinery Kits


Miller Mini Kit c/w 100 Birch Dowels  (Ref: 300589)

Miller Mini Kit c/w 100 Birch Dowels

Key Features:

-Kits available in three sizes
-Mini c/w 100 dowels
-Standard c/w 40 dowels
-Large c/w 50 dowels
-Birch Dowels
-Self-capping
-Ribs along length allow glue to adhere to material and dowel
-Drill bit supplied in initial starter pack

Mini Kit (6.5 diam. x 41.5) for timber 12 - 14mm thick.Standard Kit '1X' (10.5 diam. x 70mm) for timber 16 - 25mm thick.Large Kit '2X' (12.8 diam. x 90mm) for timber up to 32mm thick.Further packs of dowels are available for each size in Birch, Cherry, Oak or Walnut.The innovative stepped and ribbed form of these dowels (or maybe they should be called wooden nails) keeps the glue where you want it, in the joint, without the problem of compression experienced in ordinary dowel joints. The ribs grip the sides of the stepped pockets as they swell with the glue to lock them in place.The procedure is simple:Clamp or hold together the pieces to be joined.Drill the stepped hole with the Miller TruFit bit for the selected dowel size.Spread a thin layer of glue (Titebond II is recommended) on the ribbed section.Tap the dowel into the hole until fully seated.Trim off and sand level - Miller dowels are self capping - so job done!Please remember - good and accurate surface preparation of the mating surfaces is essential to the strength and neatness of the joint.TOP TIP for an interesting effect, use a Miller Dowel which contrasts with the host timber.

25.42 30.50


Quantity:  






Miller Mini Dowels - Birch (Pkt 100)  (Ref: 300503)

Miller Mini Dowels - Birch (Pkt 100)

Key Features:

-Kits available in three sizes
-Mini c/w 100 dowels
-Standard c/w 40 dowels
-Large c/w 50 dowels
-Birch Dowels
-Self-capping
-Ribs along length allow glue to adhere to material and dowel
-Drill bit supplied in initial starter pack

Mini Kit (6.5 diam. x 41.5) for timber 12 - 14mm thick.Standard Kit '1X' (10.5 diam. x 70mm) for timber 16 - 25mm thick.Large Kit '2X' (12.8 diam. x 90mm) for timber up to 32mm thick.Further packs of dowels are available for each size in Birch, Cherry, Oak or Walnut.The innovative stepped and ribbed form of these dowels (or maybe they should be called wooden nails) keeps the glue where you want it, in the joint, without the problem of compression experienced in ordinary dowel joints. The ribs grip the sides of the stepped pockets as they swell with the glue to lock them in place.The procedure is simple:Clamp or hold together the pieces to be joined.Drill the stepped hole with the Miller TruFit bit for the selected dowel size.Spread a thin layer of glue (Titebond II is recommended) on the ribbed section.Tap the dowel into the hole until fully seated.Trim off and sand level - Miller dowels are self capping - so job done!Please remember - good and accurate surface preparation of the mating surfaces is essential to the strength and neatness of the joint.TOP TIP for an interesting effect, use a Miller Dowel which contrasts with the host timber.

15.04 18.05


Quantity:  






Miller Mini Dowels - Oak (Pkt 100)  (Ref: 300534)

Miller Mini Dowels - Oak (Pkt 100)

Key Features:

-Kits available in three sizes
-Mini c/w 100 dowels
-Standard c/w 40 dowels
-Large c/w 50 dowels
-Birch Dowels
-Self-capping
-Ribs along length allow glue to adhere to material and dowel
-Drill bit supplied in initial starter pack

Mini Kit (6.5 diam. x 41.5) for timber 12 - 14mm thick.Standard Kit '1X' (10.5 diam. x 70mm) for timber 16 - 25mm thick.Large Kit '2X' (12.8 diam. x 90mm) for timber up to 32mm thick.Further packs of dowels are available for each size in Birch, Cherry, Oak or Walnut.The innovative stepped and ribbed form of these dowels (or maybe they should be called wooden nails) keeps the glue where you want it, in the joint, without the problem of compression experienced in ordinary dowel joints. The ribs grip the sides of the stepped pockets as they swell with the glue to lock them in place.The procedure is simple:Clamp or hold together the pieces to be joined.Drill the stepped hole with the Miller TruFit bit for the selected dowel size.Spread a thin layer of glue (Titebond II is recommended) on the ribbed section.Tap the dowel into the hole until fully seated.Trim off and sand level - Miller dowels are self capping - so job done!Please remember - good and accurate surface preparation of the mating surfaces is essential to the strength and neatness of the joint.TOP TIP for an interesting effect, use a Miller Dowel which contrasts with the host timber.

17.87 21.44


Quantity:  






Miller Standard Kit 1X - c/w 40 Birch Dowels  (Ref: 300590)

Miller Standard Kit 1X - c/w 40 Birch Dowels

Key Features:

-Kits available in three sizes
-Mini c/w 100 dowels
-Standard c/w 40 dowels
-Large c/w 50 dowels
-Birch Dowels
-Self-capping
-Ribs along length allow glue to adhere to material and dowel
-Drill bit supplied in initial starter pack

Mini Kit (6.5 diam. x 41.5) for timber 12 - 14mm thick.Standard Kit '1X' (10.5 diam. x 70mm) for timber 16 - 25mm thick.Large Kit '2X' (12.8 diam. x 90mm) for timber up to 32mm thick.Further packs of dowels are available for each size in Birch, Cherry, Oak or Walnut.The innovative stepped and ribbed form of these dowels (or maybe they should be called wooden nails) keeps the glue where you want it, in the joint, without the problem of compression experienced in ordinary dowel joints. The ribs grip the sides of the stepped pockets as they swell with the glue to lock them in place.The procedure is simple:Clamp or hold together the pieces to be joined.Drill the stepped hole with the Miller TruFit bit for the selected dowel size.Spread a thin layer of glue (Titebond II is recommended) on the ribbed section.Tap the dowel into the hole until fully seated.Trim off and sand level - Miller dowels are self capping - so job done!Please remember - good and accurate surface preparation of the mating surfaces is essential to the strength and neatness of the joint.TOP TIP for an interesting effect, use a Miller Dowel which contrasts with the host timber.

29.66 35.59


Quantity:  






Miller Standard Dowels 1X - Birch (Pkt 40)  (Ref: 300480)

Miller Standard Dowels 1X - Birch (Pkt 40)

Key Features:

-Kits available in three sizes
-Mini c/w 100 dowels
-Standard c/w 40 dowels
-Large c/w 50 dowels
-Birch Dowels
-Self-capping
-Ribs along length allow glue to adhere to material and dowel
-Drill bit supplied in initial starter pack

Mini Kit (6.5 diam. x 41.5) for timber 12 - 14mm thick.Standard Kit '1X' (10.5 diam. x 70mm) for timber 16 - 25mm thick.Large Kit '2X' (12.8 diam. x 90mm) for timber up to 32mm thick.Further packs of dowels are available for each size in Birch, Cherry, Oak or Walnut.The innovative stepped and ribbed form of these dowels (or maybe they should be called wooden nails) keeps the glue where you want it, in the joint, without the problem of compression experienced in ordinary dowel joints. The ribs grip the sides of the stepped pockets as they swell with the glue to lock them in place.The procedure is simple:Clamp or hold together the pieces to be joined.Drill the stepped hole with the Miller TruFit bit for the selected dowel size.Spread a thin layer of glue (Titebond II is recommended) on the ribbed section.Tap the dowel into the hole until fully seated.Trim off and sand level - Miller dowels are self capping - so job done!Please remember - good and accurate surface preparation of the mating surfaces is essential to the strength and neatness of the joint.TOP TIP for an interesting effect, use a Miller Dowel which contrasts with the host timber.

9.38 11.26


Quantity:  






Miller Standard Dowels 1X - Oak (Pkt 40)  (Ref: 300435)

Miller Standard Dowels 1X - Oak (Pkt 40)

Key Features:

-Kits available in three sizes
-Mini c/w 100 dowels
-Standard c/w 40 dowels
-Large c/w 50 dowels
-Birch Dowels
-Self-capping
-Ribs along length allow glue to adhere to material and dowel
-Drill bit supplied in initial starter pack

Mini Kit (6.5 diam. x 41.5) for timber 12 - 14mm thick.Standard Kit '1X' (10.5 diam. x 70mm) for timber 16 - 25mm thick.Large Kit '2X' (12.8 diam. x 90mm) for timber up to 32mm thick.Further packs of dowels are available for each size in Birch, Cherry, Oak or Walnut.The innovative stepped and ribbed form of these dowels (or maybe they should be called wooden nails) keeps the glue where you want it, in the joint, without the problem of compression experienced in ordinary dowel joints. The ribs grip the sides of the stepped pockets as they swell with the glue to lock them in place.The procedure is simple:Clamp or hold together the pieces to be joined.Drill the stepped hole with the Miller TruFit bit for the selected dowel size.Spread a thin layer of glue (Titebond II is recommended) on the ribbed section.Tap the dowel into the hole until fully seated.Trim off and sand level - Miller dowels are self capping - so job done!Please remember - good and accurate surface preparation of the mating surfaces is essential to the strength and neatness of the joint.TOP TIP for an interesting effect, use a Miller Dowel which contrasts with the host timber.

10.80 12.96


Quantity:  






Miller Standard Dowels 1X - Walnut (Pkt 40)  (Ref: 300459)

Miller Standard Dowels 1X - Walnut (Pkt 40)

Key Features:

-Kits available in three sizes
-Mini c/w 100 dowels
-Standard c/w 40 dowels
-Large c/w 50 dowels
-Birch Dowels
-Self-capping
-Ribs along length allow glue to adhere to material and dowel
-Drill bit supplied in initial starter pack

Mini Kit (6.5 diam. x 41.5) for timber 12 - 14mm thick.Standard Kit '1X' (10.5 diam. x 70mm) for timber 16 - 25mm thick.Large Kit '2X' (12.8 diam. x 90mm) for timber up to 32mm thick.Further packs of dowels are available for each size in Birch, Cherry, Oak or Walnut.The innovative stepped and ribbed form of these dowels (or maybe they should be called wooden nails) keeps the glue where you want it, in the joint, without the problem of compression experienced in ordinary dowel joints. The ribs grip the sides of the stepped pockets as they swell with the glue to lock them in place.The procedure is simple:Clamp or hold together the pieces to be joined.Drill the stepped hole with the Miller TruFit bit for the selected dowel size.Spread a thin layer of glue (Titebond II is recommended) on the ribbed section.Tap the dowel into the hole until fully seated.Trim off and sand level - Miller dowels are self capping - so job done!Please remember - good and accurate surface preparation of the mating surfaces is essential to the strength and neatness of the joint.TOP TIP for an interesting effect, use a Miller Dowel which contrasts with the host timber.

15.98 19.18


Quantity:  






Miller Large Joinery Kit 2X - c/w 50 Birch Dowels  (Ref: 300060)

Miller Large Joinery Kit 2X - c/w 50 Birch Dowels

Key Features:

-Kits available in three sizes
-Mini c/w 100 dowels
-Standard c/w 40 dowels
-Large c/w 50 dowels
-Birch Dowels
-Self-capping
-Ribs along length allow glue to adhere to material and dowel
-Drill bit supplied in initial starter pack

Mini Kit (6.5 diam. x 41.5) for timber 12 - 14mm thick.Standard Kit '1X' (10.5 diam. x 70mm) for timber 16 - 25mm thick.Large Kit '2X' (12.8 diam. x 90mm) for timber up to 32mm thick.Further packs of dowels are available for each size in Birch, Cherry, Oak or Walnut.The innovative stepped and ribbed form of these dowels (or maybe they should be called wooden nails) keeps the glue where you want it, in the joint, without the problem of compression experienced in ordinary dowel joints. The ribs grip the sides of the stepped pockets as they swell with the glue to lock them in place.The procedure is simple:Clamp or hold together the pieces to be joined.Drill the stepped hole with the Miller TruFit bit for the selected dowel size.Spread a thin layer of glue (Titebond II is recommended) on the ribbed section.Tap the dowel into the hole until fully seated.Trim off and sand level - Miller dowels are self capping - so job done!Please remember - good and accurate surface preparation of the mating surfaces is essential to the strength and neatness of the joint.TOP TIP for an interesting effect, use a Miller Dowel which contrasts with the host timber.

35.31 42.37


Quantity:  






Miller Large Dowels 2X - Birch (Pkt 40)  (Ref: 300497)

Miller Large Dowels 2X - Birch (Pkt 40)

Key Features:

-Kits available in three sizes
-Mini c/w 100 dowels
-Standard c/w 40 dowels
-Large c/w 50 dowels
-Birch Dowels
-Self-capping
-Ribs along length allow glue to adhere to material and dowel
-Drill bit supplied in initial starter pack

Mini Kit (6.5 diam. x 41.5) for timber 12 - 14mm thick.Standard Kit '1X' (10.5 diam. x 70mm) for timber 16 - 25mm thick.Large Kit '2X' (12.8 diam. x 90mm) for timber up to 32mm thick.Further packs of dowels are available for each size in Birch, Cherry, Oak or Walnut.The innovative stepped and ribbed form of these dowels (or maybe they should be called wooden nails) keeps the glue where you want it, in the joint, without the problem of compression experienced in ordinary dowel joints. The ribs grip the sides of the stepped pockets as they swell with the glue to lock them in place.The procedure is simple:Clamp or hold together the pieces to be joined.Drill the stepped hole with the Miller TruFit bit for the selected dowel size.Spread a thin layer of glue (Titebond II is recommended) on the ribbed section.Tap the dowel into the hole until fully seated.Trim off and sand level - Miller dowels are self capping - so job done!Please remember - good and accurate surface preparation of the mating surfaces is essential to the strength and neatness of the joint.TOP TIP for an interesting effect, use a Miller Dowel which contrasts with the host timber.

11.28 13.54


Quantity:  






Miller Large Dowels 2X - Cherry (Pkt 40)  (Ref: 300428)

Miller Large Dowels 2X - Cherry (Pkt 40)

Key Features:

-Kits available in three sizes
-Mini c/w 100 dowels
-Standard c/w 40 dowels
-Large c/w 50 dowels
-Birch Dowels
-Self-capping
-Ribs along length allow glue to adhere to material and dowel
-Drill bit supplied in initial starter pack

Mini Kit (6.5 diam. x 41.5) for timber 12 - 14mm thick.Standard Kit '1X' (10.5 diam. x 70mm) for timber 16 - 25mm thick.Large Kit '2X' (12.8 diam. x 90mm) for timber up to 32mm thick.Further packs of dowels are available for each size in Birch, Cherry, Oak or Walnut.The innovative stepped and ribbed form of these dowels (or maybe they should be called wooden nails) keeps the glue where you want it, in the joint, without the problem of compression experienced in ordinary dowel joints. The ribs grip the sides of the stepped pockets as they swell with the glue to lock them in place.The procedure is simple:Clamp or hold together the pieces to be joined.Drill the stepped hole with the Miller TruFit bit for the selected dowel size.Spread a thin layer of glue (Titebond II is recommended) on the ribbed section.Tap the dowel into the hole until fully seated.Trim off and sand level - Miller dowels are self capping - so job done!Please remember - good and accurate surface preparation of the mating surfaces is essential to the strength and neatness of the joint.TOP TIP for an interesting effect, use a Miller Dowel which contrasts with the host timber.

9.90 11.88


Quantity:  






Miller Large Dowels 2X - Oak (Pkt 40)  (Ref: 300442)

Miller Large Dowels 2X - Oak (Pkt 40)

Key Features:

-Kits available in three sizes
-Mini c/w 100 dowels
-Standard c/w 40 dowels
-Large c/w 50 dowels
-Birch Dowels
-Self-capping
-Ribs along length allow glue to adhere to material and dowel
-Drill bit supplied in initial starter pack

Mini Kit (6.5 diam. x 41.5) for timber 12 - 14mm thick.Standard Kit '1X' (10.5 diam. x 70mm) for timber 16 - 25mm thick.Large Kit '2X' (12.8 diam. x 90mm) for timber up to 32mm thick.Further packs of dowels are available for each size in Birch, Cherry, Oak or Walnut.The innovative stepped and ribbed form of these dowels (or maybe they should be called wooden nails) keeps the glue where you want it, in the joint, without the problem of compression experienced in ordinary dowel joints. The ribs grip the sides of the stepped pockets as they swell with the glue to lock them in place.The procedure is simple:Clamp or hold together the pieces to be joined.Drill the stepped hole with the Miller TruFit bit for the selected dowel size.Spread a thin layer of glue (Titebond II is recommended) on the ribbed section.Tap the dowel into the hole until fully seated.Trim off and sand level - Miller dowels are self capping - so job done!Please remember - good and accurate surface preparation of the mating surfaces is essential to the strength and neatness of the joint.TOP TIP for an interesting effect, use a Miller Dowel which contrasts with the host timber.

13.15 15.78


Quantity:  






Miller Dowel Mini - X Stepped Drill Bit  (Ref: 476813)

Miller Dowel Mini - X Stepped Drill Bit

Key Features:

-Kits available in three sizes
-Mini c/w 100 dowels
-Standard c/w 40 dowels
-Large c/w 50 dowels
-Birch Dowels
-Self-capping
-Ribs along length allow glue to adhere to material and dowel
-Drill bit supplied in initial starter pack

Mini Kit (6.5 diam. x 41.5) for timber 12 - 14mm thick.Standard Kit '1X' (10.5 diam. x 70mm) for timber 16 - 25mm thick.Large Kit '2X' (12.8 diam. x 90mm) for timber up to 32mm thick.Further packs of dowels are available for each size in Birch, Cherry, Oak or Walnut.The innovative stepped and ribbed form of these dowels (or maybe they should be called wooden nails) keeps the glue where you want it, in the joint, without the problem of compression experienced in ordinary dowel joints. The ribs grip the sides of the stepped pockets as they swell with the glue to lock them in place.The procedure is simple:Clamp or hold together the pieces to be joined.Drill the stepped hole with the Miller TruFit bit for the selected dowel size.Spread a thin layer of glue (Titebond II is recommended) on the ribbed section.Tap the dowel into the hole until fully seated.Trim off and sand level - Miller dowels are self capping - so job done!Please remember - good and accurate surface preparation of the mating surfaces is essential to the strength and neatness of the joint.TOP TIP for an interesting effect, use a Miller Dowel which contrasts with the host timber.

13.15 15.78


Quantity:  






Miller Mini Dowels - Walnut (Pkt 100)  (Ref: 300558)

Miller Mini Dowels - Walnut (Pkt 100)

Key Features:

-Kits available in three sizes
-Mini c/w 100 dowels
-Standard c/w 40 dowels
-Large c/w 50 dowels
-Birch Dowels
-Self-capping
-Ribs along length allow glue to adhere to material and dowel
-Drill bit supplied in initial starter pack

Mini Kit (6.5 diam. x 41.5) for timber 12 - 14mm thick.Standard Kit '1X' (10.5 diam. x 70mm) for timber 16 - 25mm thick.Large Kit '2X' (12.8 diam. x 90mm) for timber up to 32mm thick.Further packs of dowels are available for each size in Birch, Cherry, Oak or Walnut.The innovative stepped and ribbed form of these dowels (or maybe they should be called wooden nails) keeps the glue where you want it, in the joint, without the problem of compression experienced in ordinary dowel joints. The ribs grip the sides of the stepped pockets as they swell with the glue to lock them in place.The procedure is simple:Clamp or hold together the pieces to be joined.Drill the stepped hole with the Miller TruFit bit for the selected dowel size.Spread a thin layer of glue (Titebond II is recommended) on the ribbed section.Tap the dowel into the hole until fully seated.Trim off and sand level - Miller dowels are self capping - so job done!Please remember - good and accurate surface preparation of the mating surfaces is essential to the strength and neatness of the joint.TOP TIP for an interesting effect, use a Miller Dowel which contrasts with the host timber.

26.83 32.20


Quantity:  






Miller Dowel - 2X Stepped Drill Bit  (Ref: 475760)

Miller Dowel - 2X Stepped Drill Bit

Key Features:

-Kits available in three sizes
-Mini c/w 100 dowels
-Standard c/w 40 dowels
-Large c/w 50 dowels
-Birch Dowels
-Self-capping
-Ribs along length allow glue to adhere to material and dowel
-Drill bit supplied in initial starter pack

Mini Kit (6.5 diam. x 41.5) for timber 12 - 14mm thick.Standard Kit '1X' (10.5 diam. x 70mm) for timber 16 - 25mm thick.Large Kit '2X' (12.8 diam. x 90mm) for timber up to 32mm thick.Further packs of dowels are available for each size in Birch, Cherry, Oak or Walnut.The innovative stepped and ribbed form of these dowels (or maybe they should be called wooden nails) keeps the glue where you want it, in the joint, without the problem of compression experienced in ordinary dowel joints. The ribs grip the sides of the stepped pockets as they swell with the glue to lock them in place.The procedure is simple:Clamp or hold together the pieces to be joined.Drill the stepped hole with the Miller TruFit bit for the selected dowel size.Spread a thin layer of glue (Titebond II is recommended) on the ribbed section.Tap the dowel into the hole until fully seated.Trim off and sand level - Miller dowels are self capping - so job done!Please remember - good and accurate surface preparation of the mating surfaces is essential to the strength and neatness of the joint.TOP TIP for an interesting effect, use a Miller Dowel which contrasts with the host timber.

25.42 30.50


Quantity:  






Miller Dowel - 1X Stepped Drill Bit  (Ref: 476062)

Miller Dowel - 1X Stepped Drill Bit

Key Features:

-Kits available in three sizes
-Mini c/w 100 dowels
-Standard c/w 40 dowels
-Large c/w 50 dowels
-Birch Dowels
-Self-capping
-Ribs along length allow glue to adhere to material and dowel
-Drill bit supplied in initial starter pack

Mini Kit (6.5 diam. x 41.5) for timber 12 - 14mm thick.Standard Kit '1X' (10.5 diam. x 70mm) for timber 16 - 25mm thick.Large Kit '2X' (12.8 diam. x 90mm) for timber up to 32mm thick.Further packs of dowels are available for each size in Birch, Cherry, Oak or Walnut.The innovative stepped and ribbed form of these dowels (or maybe they should be called wooden nails) keeps the glue where you want it, in the joint, without the problem of compression experienced in ordinary dowel joints. The ribs grip the sides of the stepped pockets as they swell with the glue to lock them in place.The procedure is simple:Clamp or hold together the pieces to be joined.Drill the stepped hole with the Miller TruFit bit for the selected dowel size.Spread a thin layer of glue (Titebond II is recommended) on the ribbed section.Tap the dowel into the hole until fully seated.Trim off and sand level - Miller dowels are self capping - so job done!Please remember - good and accurate surface preparation of the mating surfaces is essential to the strength and neatness of the joint.TOP TIP for an interesting effect, use a Miller Dowel which contrasts with the host timber.

20.69 24.83


Quantity:  






Woodworking Tools >  Miller Dowel Joinery Kits



Miller Dowel Joinery Kits
Buy online at www.quality-woodworking-tools.com with FREE mainland UK delivery for all woodworking tools





Woodworking Tools Homepage
checkout
  View Basket
Woodworking Tools UK Delivery
Free UK Delivery
New ! - Arbortech Ball Gouge SPECIAL OFFER WHEEL MARKING GAUGE Digital Depth Gauge for Routers etc Soba Wood Worker Set- £10 off - Last Few at This Price !!! New Nova Woodturning Lathes NOVA 1624 II Lathe Andy King Striking Knives Signature Range NEW !! Nova Wood Turning Chucks & Accessories SCT Woodworking Chucks , Centres , Faceplates Countersinks etc Elipse Respirators Range Bench Dog Woodworking Accessories Kreg Woodworking Jigs & Tools Kunz Quality German Woodworking Tools Pinie Quality Woodworking & Carpentry Tools Dalmann Mallets Range Premium Bandsaw Blades Sjobergs Swedish Work Benches Winbag Air Wedge Tool Mirka Abrasives Tormek Sharpening Tools Veritas Woodwork Hand Tools Soba Precision Woodworking Planes & Tools Arbortech Power Carving Rotarex Carving & Shaping Discs Sandipads Hook & Loop Sanding System Triton Woodworking Machines Axminister Edgebander Brimarc Braces Bencil Carpenters Pencils Co-Matic Power Feeds Duragrit Rotary Tools & Burrs Johnson Tools Rasps & Rifflers Johnson Sharpening Suppplies Eze-lap Diamond Sharpening Hones & Stones Dust Extraction Accessories Flexcut 5 Piece Printmaking Set Flexcut Carving Tools Beber Carving Tools Range Proxxon Woodworking Tools GemRed Digital Angle Measuring Shogun High Quality Japanese Saws Ice Bear Japanese Tools Naniwa Waterstones Asahi Japanese Woodworking Tools Pyrography Jet Woodworking Machinery Microplane Razor Sharp Rasps Miller Dowel Joinery Kits Nobex Carpentry Tools Woodworking Glues & Adhesives Wooden Toolchests & Storage Boxes Woodcraft Jigs , Screws & Tools UJK SOLID BEECH BISCUITS Pegas Scroll & Coping Saw Blades Zona Razor Saws Pen Kits & Accessories Spraycraft Airbrush Equipment Axminster Pen & Pencil Kits Clarke Woodworking Tools & Machinery Draper Woodworking Tools & Machinery srt stuff

Newsletter Subscription